crank arm

The RW Series Rotary Actuator design utilizes two independent piston cylinders, each piston has a crank arm attached to a crankshaft.

在RW系列旋转式驱动器设计采用两个独立的活塞筒，每个活塞有曲柄连接曲轴臂。

Due to complex mechanical motion of the crank rocker arm of rice transplanter, we depend on miscellaneous math inference in teaching, which is insipid and indirect.

插秧机曲柄摇杆机构运动十分复杂，教学中依靠繁琐的公式推导，既枯燥又不直观。

Operations on multi-points are available through the crank arm framework.

多点式操作可通过曲柄臂框架。其结构简单轻便，运作畅顺。

The machining of deep bolt holes in the air compressor's crank arm Machining of Threaded Holes in Engine Con Rods

空压机连杆两螺栓孔的深加工6102柴油机连杆螺栓孔的加工

Affix using one of the crank arm fixing bolts.

词缀使用其中的一个曲柄臂固定螺栓。

The crankshaft machining complex lathe turned the crank arm journal with the way of servo turning methods.

曲轴加工复合车床通过随动车削的方式对曲轴连杆轴颈进行加工。

STUDY ON A NEW TYPE OF MOBILE ROBOT MECHANISM MOVING IN PIPE Computer Simulation of A Complex Crank Rocker Arm Mechanism Moving

直进轮式全驱动管内行走机构的研究一种复杂曲柄摇杆机构运动学的计算机仿真

Begin with the analysis and the investigation of the basic principle chart of illustrated diagram method of type ⅰ and ⅱ institution of plane crank jointed arm which is designed according to the stroke velocity ratio coefficient.

从分析、考察按行程速比系数K设计ⅠI型、Ⅱ型平面曲柄摇杆机构图解法的基本原理图入手，对最佳辅助角λ（？）

To raise the polishing efficiency of Cubic boron nitride ( CBN) superhard material, crank rocker arm mechanism has been developed by using Computer Simulation Technology.

为了提高立方氮化硼超硬材料的抛光效率，采用计算机仿真技术开发了曲柄摇杆抛光机构。

Crank and Rocker Arm Shear's Kinematics Analysis Based on Matlab

基于Matlab的曲柄摇杆式飞剪运动学分析研究

The utility model is composed of a land wheel, a driving pin, a driving crank arm, a driving inserted link, a release spring, and a driving ratchet.

它由地轮、传动销、传动拐臂、传动插杆、回位弹簧和传动棘轮组成。

With the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is.

以第3阶和第4阶固有频率振动，位置越靠近曲轴第二个曲柄臂与主轴过渡圆处固有频率越小。

The crankshafts shown in Fig1-4 is actually made up of various parts such as main bearing journals, rod journal, crank arm, bearing, counter balanced weight and flywheel end.

在图1-4中，曲轴实际上由以下不同的部分组成，它们分别是：主轴承轴颈、连杆轴颈、曲轴臂、轴承、平衡配量（？）以及飞轮端。

Turn the wiper module over and remove the nut that secures the wiper motor crank arm to the wiper motor output shaft.

转动雨刷模组盖，并拆下将雨刷马达曲柄臂固定于雨刷马达输出轴上的螺帽。

Computer Simulation of A Complex Crank Rocker Arm Mechanism Moving

一种复杂曲柄摇杆机构运动学的计算机仿真

These simulation results, videotape of static and dynamic state of crank rocker arm mechanism and practice in farmland have been used in multi-media teaching and receive good effect.

结合曲柄摇杆机构静态、动态及田间工作实况拍成的录像片，应用于多媒体教学中，收到了良好的效果。

To power the machine, several people would turn a crank arm connected to the vacuum pump.

要操作此机器, 需要几个人转动与真空泵相连的曲柄装置.

The upper and lower seal valve are changed from that of crank structure to straight arm structure that only actuates single action, as a result, the equipment failure rate and unscheduled down time are reduced;

上下密封阀由直动+转动的曲臂结构改为转动单一动作的直臂结构，减少了设备故障率和非计划检修时间；